Updated Feb 10, 2025 Test Engine to Practice Test for FCP_FGT_AD-7.4 Valid and Updated Dumps
Exam Questions for FCP_FGT_AD-7.4 Updated Versions With Test Engine
NEW QUESTION # 32
An administrator has configured the following settings:
What are the two results of this configuration? (Choose two.)
- A. Denied users are blocked for 30 minutes.
- B. The number of logs generated by denied traffic is reduced.
- C. Device detection on all interfaces is enforced for 30 minutes.
- D. A session for denied traffic is created.
Answer: B,D
Explanation:
A session for denied traffic is created.
The command set ses-denied-traffic enable ensures that sessions for denied traffic are logged, meaning a session will be created for traffic that is denied by security policies.
The number of logs generated by denied traffic is reduced.
The set block-session-timer 30 command sets a timer to prevent excessive logging of denied traffic within a short period, which helps reduce the number of logs generated by repeated denied traffic sessions. This timer blocks sessions for a specified period (30 seconds in this case) to avoid overwhelming the log system with repetitive entries.
NEW QUESTION # 33
Which three statements about SD-WAN zones are true? (Choose three.)
- A. You can define up to three SD-WAN zones per FortiGate device
- B. An SD-WAN zone must contains at least two members
- C. You can use an SD-WAN zone in static route definitions
- D. An SD-WAN zone is a logical grouping of members
- E. An SD-WAN zone can contain physical and logical interfaces
Answer: C,D,E
Explanation:
An SD-WAN zone can contain physical and logical interfaces
SD-WAN zones can include both physical and logical interfaces, allowing flexible configuration for different network types.
You can use an SD-WAN zone in static route definitions
SD-WAN zones can be referenced in static routes, enabling dynamic path selection based on SD-WAN rules.
An SD-WAN zone is a logical grouping of members
An SD-WAN zone is a logical grouping of interfaces (members), used to simplify the management and application of SD-WAN rules.
NEW QUESTION # 34
Refer to the exhibit, which shows a partial configuration from the remote authentication server.
Why does the FortiGate administrator need this configuration?
- A. To set up a RADIUS server Secret
- B. To authenticate and match the Training OU on the RADIUS server.
- C. To authenticate Any FortiGate user groups.
- D. To authenticate only the Training user group.
Answer: B
Explanation:
The configuration shown in the exhibit indicates that the FortiGate is using a Fortinet-specific RADIUS attribute (Fortinet-Group-Name) with the value "Training." This setup allows the FortiGate to authenticate users against the RADIUS server and match them to the "Training" Organizational Unit (OU). By doing so, only users within this specific group or OU can be authenticated and allowed access through the FortiGate.
References:
* FortiOS 7.4.1 Administration Guide: RADIUS Server Configuration
NEW QUESTION # 35
Refer to the exhibits.
The exhibits show a diagram of a FortiGate device connected to the network, as well as the firewall policy and IP pool configuration on the FortiGate device.
Two PCs, PC1 and PC2, are connected behind FortiGate and can access the internet successfully. However, when the administrator adds a third PC to the network (PC3), the PC cannot connect to the internet.
Based on the information shown in the exhibit, which two configuration options can the administrator use to fix the connectivity issue for PC3? (Choose two.)
- A. In the IP pool configuration, set cype to overload.
- B. In the IP pool configuration, set endig to 192.2.0.12.
- C. In the firewall policy configuration, add 10. o. l. 3 as an address object in the source field.
- D. Configure another firewall policy that matches only the address of PC3 as source, and then place the policy on top of the list.
Answer: A,B
Explanation:
To resolve the issue of PC3 not being able to access the internet, the administrator needs to adjust the IP pool configuration or the firewall policy. The following two options will fix the connectivity issue:
B . In the IP pool configuration, set the ending IP to 192.2.0.12: The current IP pool range is 192.2.0.10-192.2.0.11, which only provides two IP addresses for network address translation (NAT). To allow PC3 to access the internet, the IP pool should be expanded to include an additional IP address by changing the end of the range to 192.2.0.12.
D . In the IP pool configuration, set type to overload: Instead of using a one-to-one NAT, changing the type to overload will allow multiple internal addresses (such as PC1, PC2, and PC3) to share a single external IP address. This will solve the issue without needing additional public IP addresses.
The other options are not suitable:
A . In the firewall policy configuration, add 10.0.1.3 as an address object in the source field: This option is unnecessary since the firewall policy already allows all addresses from the source (LAN port3).
C . Configure another firewall policy that matches only the address of PC3 as the source, and then place the policy on top of the list: This option is redundant and would not resolve the underlying issue with the IP pool configuration.
Reference
FortiOS 7.4.1 Administration Guide - Configuring Firewall Policies, page 512.
FortiOS 7.4.1 Administration Guide - Configuring NAT with IP Pools, page 518.
NEW QUESTION # 36
Why does FortiGate keep TCP sessions in the session table for some seconds even after both sides (client and server) have terminated the session?
- A. To allow for out-of-order packets that could arrive after the FIN/ACK packets.
- B. To finish any inspection operations.
- C. To remove the NAT operation.
- D. To generate logs
Answer: A
Explanation:
To allow for out-of-order packets that could arrive after the FIN/ACK packets.
TCP provides the ability for one end of a connection to terminate its output while still receiving data from the other end. This is called a half-close. FortiGate unit implements a specific timer before removing an entry in the firewall session table.
When a session is closed by both sides, FortiGate keeps it in the session table for a few seconds more, to allow any out-of-order packets that could arrive after the FIN/ACK packet. This is the state value. One of the reasons FortiGate keeps TCP sessions in the session table for several seconds, even after both sides have terminated the session, is indeed to allow for out-of-order packets that could arrive after the FIN/ACK packets. This helps in handling potential network delays and ensuring that all relevant packets are processed before fully closing the session.
NEW QUESTION # 37
An administrator wants to block https://www.example.com/videos and allow all other URLs on the website.
What are two configuration changes that the administrator can make to satisfy the requirement? (Choose two.)
- A. Configure a static URL filter entry for the URL and select Block as the action
- B. Configure a video filter profile to block the URL
- C. Configure web override for the URL and select a blocked FortiGuard subcategory
- D. Enable full SSL inspection
Answer: A,D
Explanation:
If the goal is to block the specific URL https://www.example.com/videos and allow all other URLs on the website, the correct configuration changes are:
B. Enable full SSL inspection.
Enabling full SSL inspection allows the FortiGate to inspect and filter HTTPS traffic, including the specific URL https://www.example.com/videos.
D. Configure a static URL filter entry for the URL and select Block as the action.
Create a static URL filter entry for the specific URL https://www.example.com/videos and set the action to Block. This will block access to the specified URL.
Enabling full SSL inspection is necessary to inspect and filter HTTPS traffic effectively, including the specific URL within the encrypted traffic.
So, the correct choices are B and D.
NEW QUESTION # 38
Refer to the exhibits.
Exhibit A.
Exhibit B.
An administrator creates a new address object on the root FortiGate (Local-FortiGate) in the security fabric. After synchronization, this object is not available on the downstream FortiGate (ISFW).
What must the administrator do to synchronize the address object?
- A. Change the csf setting on Local-FortiGate (root) to set fabric-object-unification default.
- B. Change the csf setting on ISFW (downstream) to set configuration-sync local.
- C. Change the csf setting on ISFW (downstream) to set fabric-object-unification default.
- D. Change the csf setting on Local-FortiGate (root) to set configuration-sync local.
Answer: A
Explanation:
Change the csf setting on Local-FortiGate (root) to set fabric-object-unification default.
The CLI command set fabric-object-unification is only available on the root FortiGate. When set to local, global objects will not be synchronized to downstream devices in the Security Fabric. The default value is default.
Option A will not synchronise global fabric objects downstream.
NEW QUESTION # 39
Which three statements are true regarding session-based authentication? (Choose three.)
- A. HTTP sessions are treated as a single user.
- B. It can differentiate among multiple clients behind the same source IP address.
- C. IP sessions from the same source IP address are treated as a single user.
- D. It is not recommended if multiple users are behind the source NAT
- E. It requires more resources.
Answer: A,B,E
Explanation:
These three statements are indeed true regarding session-based authentication:
A. HTTP sessions are treated as a single user: Session-based authentication can treat multiple HTTP sessions as a single user, providing a consolidated view of user activity.
C. It can differentiate among multiple clients behind the same source IP address: Session-based authentication is capable of distinguishing between multiple clients behind the same source IP address.
D. It requires more resources: Session-based authentication may require more resources compared to simpler authentication methods due to the additional processing involved in tracking and managing user sessions.
For A: Each session-based authenticated user is counted as a single user using their authentication membership (RADIUS, LDAP, FSSO, local database etc.) to match users in other sessions. So one authenticated user in multiple sessions is still one user.
NEW QUESTION # 40
Refer to the exhibits.
The exhibits show a diagram of a FortiGate device connected to the network, and the firewall configuration.
An administrator created a Deny policy with default settings to deny Webserver access for Remote-User2.
The policy should work such that Remote-User1 must be able to access the Webserver while preventing Remote-User2 from accessing the Webserver.
Which two configuration changes can the administrator make to the policy to deny Webserver access for Remote-User2? (Choose two.)
- A. Enable match-vip in the Deny policy.
- B. Disable match-vip in the Deny policy.
- C. Set the Destination address as Deny_IP in the Allow_access policy.
- D. Set the Destination address as Webserver in the Deny policy.
Answer: A,D
Explanation:
To deny access to the web server for Remote-User2 while allowing Remote-User1 to access the same web server, two configuration changes can be made:
Enable match-vip in the Deny policy:
By enabling the match-vip option in the Deny policy, the FortiGate will check for virtual IP (VIP) objects during policy matching. This setting allows the firewall policy to correctly identify and block traffic directed to a specific mapped IP address, such as the web server, when using a VIP configuration.
Set the Destination address as Webserver in the Deny policy:
Setting the Destination address to "Webserver" in the Deny policy ensures that the policy specifically targets traffic attempting to reach the web server. This configuration helps to precisely control which traffic should be blocked, focusing the Deny policy on the intended destination.
Reference:
FortiOS 7.4.1 Administration Guide: Deny matching with a policy with a virtual IP applied FortiOS 7.4.1 Administration Guide: Configuring Policies with VIPs
NEW QUESTION # 41
Which two statements are correct about SLA targets? (Choose two.)
- A. SLA targets are used only when referenced by an SD-WAN rule.
- B. You can configure only two SLA targets per one Performance SLA.
- C. SLA targets are optional.
- D. SLA targets are required for SD-WAN rules with a Best Quality strategy.
Answer: A,C
Explanation:
B). SLA targets are optional.
D). SLA targets are used only when referenced by an SD-WAN rule.
Incorrect:
A). You can configure only two SLA targets per one Performance SLA. (more is possible)
C). SLA targets are required for SD-WAN rules with a Best Quality strategy. (not required) If the health check is used in an SD-WAN rule that uses Manual or Best Quality strategies, enabling SLA Target is optional. If the health check is used in an SD-WAN rule that uses Lowest Cost (SLA) or Maximum Bandwidth (SLA) strategies, then SLA Target is enabled.
Enable SLA Targetsand configure the constraints. To add multiple SLA targets, use the CLI.
NEW QUESTION # 42
Refer to the exhibit.
Based on the routing database shown in the exhibit which two conclusions can you make about the routes?
(Choose two.)
- A. The port1 and port2 default routes are active in the routing table
- B. The port3 default route has the lowest metric
- C. The port3 default route has the highest distance
- D. There will be eight routes active in the routing table
Answer: A,C
Explanation:
The port1 and port2 default routes are active in the routing table
The routes with 0.0.0.0/0 for both port1 and port2 are marked with an asterisk * and > symbol, which indicates that these routes are active and selected in the routing table.
The port3 default route has the highest distance
The route via port3 has a distance of [20/0], which is higher than the distances for the routes via port1 [10/0] and port2 [30/0]. This indicates that the port3 default route has the highest distance.
NEW QUESTION # 43
If Internet Service is already selected as Source in a firewall policy, which other configuration objects can be added to the Source field of a firewall policy?
- A. User or User Group
- B. Once Internet Service is selected, no other object can be added
- C. IP address
- D. FQDN address
Answer: A
Explanation:
C is correct and tested (user added and user group are added to policy but ip address or network failed to add) We have just confirmed this on a Production Fortigate FW and you can add user/User group but you cannot add Address group with ISDB object. It will simply show a red highlighted error which is read as
"Addresses/groups cannot be mixed with Internet Services"
if src: you can add user, if dst: you cannot add any other object.
You can't mix ISDB objects with regular address objects. User objects are not restricted in any way.
NEW QUESTION # 44
Consider the topology:
Application on a Windows machine <--{SSL VPN} -->FGT--> Telnet to Linux server.
An administrator is investigating a problem where an application establishes a Telnet session to a Linux server over the SSL VPN through FortiGate and the idle session times out after about 90 minutes. The administrator would like to increase or disable this timeout.
The administrator has already verified that the issue is not caused by the application or Linux server.
This issue does not happen when the application establishes a Telnet connection to the Linux server directly on the LAN.
What two changes can the administrator make to resolve the issue without affecting services running through FortiGate? (Choose two.)
- A. Create a new service object for TELNET and set the maximum session TTL.
- B. Create a new firewall policy and place it above the existing SSLVPN policy for the SSL VPN traffic, and set the new TELNET service object in the policy.
- C. Set the maximum session TTL value for the TELNET service object.
- D. Set the session TTL on the SSLVPN policy to maximum, so the idle session timeout will not happen after 90 minutes.
Answer: A,B
Explanation:
The key here is performing the task without affecting any of the other services.
C. Create a new service object for TELNET and set the maximum session TTL: By creating a new service object specifically for TELNET and setting the maximum session TTL, you can control the idle session timeout for Telnet connections established through the SSL VPN.
D. Create a new firewall policy and place it above the existing SSLVPN policy for the SSL VPN traffic, and set the new TELNET service object in the policy: Creating a new firewall policy and placing it above the existing SSLVPN policy allows you to apply the new TELNET service object with the modified session TTL, ensuring that the idle session timeout does not occur after 90 minutes.
- Not A - Changing the maximum TTL value for TELNET will affect every other policy that references the TELNET service
- Not B - Changing the session TTL on the SSLVPN policy will impact other services referenced in the policy.
NEW QUESTION # 45
Refer to the exhibit.
The exhibit shows the IPS sensor configuration.
If traffic matches this IPS sensor, which two actions is the sensor expected to take? (Choose two.)
- A. The sensor will gather a packet log for all matched traffic.
- B. The sensor will block all attacks aimed at Windows servers.
- C. The sensor will reset all connections that match these signatures.
- D. The sensor will allow attackers matching the NTP.Spoofed.KoD.DoS signature.
Answer: B,D
Explanation:
The correct answers are:
A. The sensor will allow attackers matching the NTP.Spoofed.KoD.DoS signature.
B. The sensor will block all attacks aimed at Windows servers.
For option A, the sensor is configured to "Deny Attacker Inline" for the NTP.Spoofed.KoD.DoS signature, which means it will block traffic matching this signature.
For option B, the sensor is configured to "Deny Attacker Inline" for the Windows Servers category, which means it will block all attacks aimed at Windows servers.
NEW QUESTION # 46
Which two pieces of information are synchronized between FortiGate HA members? (Choose two.)
- A. IPsec security associations
- B. OSPF adjacencies
- C. BGP peerings
- D. DHCP leases
Answer: A,D
Explanation:
IPsec security associations
IPsec security associations (SAs) are synchronized between HA members to ensure seamless failover and continuity of VPN tunnels.
DHCP leases
DHCP lease information is synchronized between HA members to maintain consistent IP address assignments and prevent disruptions when failover occurs.
NEW QUESTION # 47
Which type of logs on FortiGate record information about traffic directly to and from the FortiGate management IP addresses?
- A. Forward traffic logs
- B. Security logs
- C. System event logs
- D. Local traffic logs
Answer: D
Explanation:
The type of logs on FortiGate that records information about traffic directly to and from the FortiGate nmanagement IP addresses is:
A. Local traffic logs
Local traffic logs include information about traffic that is directed to and from the FortiGate unit itself, including traffic to and from the FortiGate management IP addresses. These logs provide details about communication involving the FortiGate device.
So, the correct choice is A.
NEW QUESTION # 48
Refer to the exhibit, which contains a session list output.
Based on the information shown in the exhibit, which statement is true?
- A. Port block allocation IP pool is used in the firewall policy
- B. Destination NAT is disabled in the firewall policy
- C. Overload NAT IP pool is used in the firewall policy
- D. One-to-one NAT IP pool is used in the firewall policy
Answer: D
Explanation:
One-to-one NAT IP pool is used in the firewall policy.
In one-to-one, PAT is not required.
In the one-to-one pool type, an internal IP address is mapped with an external address on a first-come, first-served basis.
There is a single mapping of an internal address to an external address. Mappings are not fixed and, if there are no more addresses available, a connection will be refused.
Also, in one-to-one, PAT is not required. In the example on this slide, you can see the same source port is shown for both the ingress and egress address.
NEW QUESTION # 49
An administrator has configured the following settings:
What are the two results of this configuration? (Choose two.)
- A. Device detection on all interfaces is enforced for 30 minutes
- B. A session for denied traffic is created
- C. Denied users are blocked for 30 minutes
- D. The number of logs generated by denied traffic is reduced
Answer: B,D
Explanation:
C: A session for denied traffic is created.
D: The number of logs generated by denied traffic is reduced.
During the session, if a security profile detects a violation, FortiGate records the attack log immediately.
To reduce the number of log messages generated and improve performance, you can enable a session table entry of dropped traffic. This creates the denied session in the session table and, if the session is denied, all packets of that session are also denied. This ensures that FortiGate does not have to do a policy lookup for each new packet matching the denied session, which reduces CPU usage and log generation.
This option is in the CLI, and is called ses-denied-traffic. You can also set the duration for block sessions.
This determines how long a session will be kept in the session table by setting block-sessiontimer in the CLI. By default, it is set to 30 seconds.
NEW QUESTION # 50
Examine this FortiGate configuration:
Examine the output of the following debug command:
Based on the diagnostic outputs above, how is the FortiGate handling the traffic for new sessions that require inspection?
- A. It is allowed, but with no inspection
- B. It is allowed and inspected, as long as the only inspection required is antivirus.
- C. It is dropped.
- D. It is allowed and inspected as long as the inspection is flow based
Answer: C
Explanation:
C because it exceeded the Extreme memory threshold.
"However, if the memory usage exceeds the extreme threshold, new sessions are ALWAYS DROPPED, regardless of the FortiGate configuration." if the memory usage keeps increasing, it might exceed the extreme threshold. While the memory usage is above this highest threshold, all new sessions are dropped.
Note: "Extreme threshold is when the memory usage goes above 95%, and all NEW sessions are dropped.
NEW QUESTION # 51
Refer to the exhibit.
In the network shown in the exhibit, the web client cannot connect to the HTTP web server. The administrator runs the FortiGate built-in sniffer and gets the output shown in the exhibit.
What should the administrator do next, to troubleshoot the problem?
- A. Capture the traffic using an external sniffer connected to part1.
- B. Run a sniffer on the web server.
- C. Execute a debug flow.
- D. Execute another sniffer on FortiGate, this time with the filter "hose 10.o.1.10".
Answer: C
Explanation:
The sniffer output shows that packets from the web client are reaching the FortiGate and being forwarded to the web server, but there is no indication that the web server is responding. To troubleshoot this issue, executing a debug flow will help analyze the traffic path and pinpoint where the problem might be occurring, such as a possible issue in firewall policy or route settings that is causing the server not to respond correctly.
Reference:
FortiOS 7.4.1 Administration Guide: Troubleshooting network connectivity
NEW QUESTION # 52
Refer to the exhibit.
The exhibit shows the FortiGuard Category Based Filter section of a corporate web filter profile.
An administrator must block access to download.com, which belongs to the Freeware and Software Downloads category. The administrator must also allow other websites in the same category.
What are two solutions for satisfying the requirement? (Choose two.)
- A. Set the Freeware and Software Downloads category Action to Warning
- B. Configure a static URL filter entry for download, com with Type and Action set to Wildcard and Block, respectively.
- C. Configure a web override rating for download, com and select Malicious Websites as the subcategory.
- D. Configure a separate firewall policy with action Deny and an FQDN address object for *. download, com as destination address.
Answer: B,D
Explanation:
To block access specifically to download.com while allowing other sites in the "Freeware and Software Downloads" category, you can create a separate firewall policy with a deny action specifically for the FQDN
*.download.com. This approach allows blocking this particular site without affecting the other sites in the same category. Alternatively, configuring a static URL filter entry with the type set to Wildcard and action set to Block will also achieve the desired effect by directly blocking the specific URL without impacting other sites in the category.
References:
* FortiOS 7.4.1 Administration Guide: URL filter configuration
NEW QUESTION # 53
Which two statements correctly describe auto discovery VPN (ADVPN)? (Choose two.)
- A. IPSec tunnels are negotiated dynamically between spokes.
- B. It recommends the use of dynamic routing protocols, so that spokes can learn the routes to other spokes.
- C. ADVPN is supported only with IKEv2.
- D. Every spoke requires a static tunnel to be configured to other spokes, so that phase 1 and phase 2 proposals are defined in advance.
Answer: A,B
Explanation:
The correct statements describing auto discovery VPN (ADVPN) are:
A. IPSec tunnels are negotiated dynamically between spokes.
C. It recommends the use of dynamic routing protocols, so that spokes can learn the routes to other spokes.
A. In ADVPN, tunnels are negotiated dynamically between spokes, meaning that spokes do not need to have predefined static tunnels. The spokes dynamically establish tunnels based on the requirements, which can simplify the configuration and management of VPN connections.
C. ADVPN often relies on dynamic routing protocols (such as OSPF or BGP) to allow spokes to dynamically learn routes to other spokes. This dynamic behavior enhances scalability and ease of configuration.
Option B is incorrect because ADVPN is not limited to IKEv2; it can be used with IKEv1 as well.
Option D is incorrect because ADVPN is designed to establish tunnels dynamically, and it doesn't require every spoke to have static tunnels configured in advance.
NEW QUESTION # 54
Refer to the exhibit.
An administrator has configured a performance SLA on FortiGate, which failed to generate any traffic.
Why is FortiGate not sending probes to 4.2.2.2 and 4.2.2.1 servers? (Choose two.)
- A. The Detection Mode setting is not set to Passive.
- B. Administrator didn't configure a gateway for the SD-WAN members, or configured gateway is not valid.
- C. The Enable probe packets setting is not enabled.
- D. The configured participants are not SD-WAN members.
Answer: B,C
Explanation:
The correct answers are:
B. Administrator didn't configure a gateway for the SD-WAN members, or configured gateway is not valid.
D. The Enable probe packets setting is not enabled.
Explanation:
For option B, if the gateway for the SD-WAN members is not configured or is not valid, the FortiGate will not be able to send traffic through the SD-WAN members to reach the servers.
For option D, if the "Enable probe packets" setting is not enabled, the FortiGate will not send probe packets to the specified servers to check the health of the SD-WAN members.
A. The Detection Mode setting is not set to Passive.
NO - passive mode uses session information from the configured policy
C. The configured participants are not SD-WAN members.
NO - It is not possible to add participants that do not belong to the SW-WAN
NEW QUESTION # 55
Which of the following statements is true regarding SSL VPN settings for an SSL VPN portal?
- A. By default, the admin GUI and SSL VPN portal use the same HTTPS port.
- B. By default, the SSL VPN portal requires the installation of a client's certificate.
- C. By default, split tunneling is enabled.
- D. By default, FortiGate uses WINS servers to resolve names.
Answer: C
Explanation:
There is a Trap here... C and D have something right but the trick is the question...
Under SSL VPN settings you can see that port is 443 (same of https admin port) BUT the question is about a SSL VPN Setting FOR A VPN PORTAL... so if you go to SSL VPN Portals and hit "Create new" you will see Tunnel Mode and Split Tunnel enabled by default... so, the correct answer is C.
Split tunneling is a feature that allows a remote VPN user to tunnel only specific, protected traffic back to the corporate network, while other traffic (e.g., internet traffic) is sent directly to its destination. This can help optimize bandwidth usage and reduce the load on the corporate network.
In the context of SSL VPN settings for an SSL VPN portal on FortiGate, if split tunneling is enabled by default, it means that the remote user's internet-bound traffic will not be forced through the corporate network but will be sent directly to the internet. This can improve performance and reduce latency for non-corporate internet traffic.
Extra explanation:
https://help.fortinet.com/fos50hlp/56/Content/FortiOS/fortigate-
sslvpn/SSLVPN_Examples/Split_Tunnel.htm#:~:text=Split%20Tunnel,SSL%20VPN%20on%20FortiGate
%20units.
NEW QUESTION # 56
......
FCP_FGT_AD-7.4 Exam Dumps - Free Demo & 365 Day Updates: https://lead2pass.guidetorrent.com/FCP_FGT_AD-7.4-dumps-questions.html